CtD | Creating The Difference
TruCut Sanding Pads - 6" Singles: 0500
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 80, 120, 220/240- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 6" Singles: 1000
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 80, 120, 220/240- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 6" Singles: 2000
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 80, 120, 220/240- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 5" Singles
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Diameter of 5 inches - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 5" Singles
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Diameter of 5 inches - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 6" Singles: 1500
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 80, 120, 220/240- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 5" Singles
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Diameter of 5 inches - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 6" Singles: 3000
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 80, 120, 220/240- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
That Purple Stuff | Bowling Ball Cleaner - 8oz (236ml)
Bowling balls get dirty. It's a fact of the game. Why pay someone else to clean your bowling ball when you can do it yourself? That Purple Stuff was is a specially formulated bowling ball cleaner that will help any bowler keep their equipment performing great. Simply apply to a CtD Power Pad and wipe the entire surface of the bowling ball to remove the dirt and oil.Tired of leaving that flat 10 pin? This bowling ball cleaner will bring back the tackiness your bowling ball had when it was new. You'll get the reaction you need to stop leaving corner pins.
Content: 0.237 Liter (€92.62 / 1 Liter)
TruCut Sanding Pads - 6" Singles: 4000
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 80, 120, 220/240- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 6" Singles: P5000D
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 80, 120, 220/240- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 5" Singles
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Diameter of 5 inches - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 5" Singles
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Diameter of 5 inches - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 5" Singles
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Diameter of 5 inches - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 6" Singles: 0240
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 80, 120, 220/240- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 5" Singles
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Diameter of 5 inches - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
Life After Death | Bowling Ball Cleaner + Life Extender - 8oz (236ml)
This product is a cleaner that is made to be absorbed by the bowling ball. It is designed to keep your bowling ball tacky longer and last 3 to 5 games. Apply this product directly on your bowling ball before and after bowling. Let it sit for 20 to 30 seconds and wipe dry. Then use That Purple Stuff or That Wow Factor Ball Cleaner for an extra tacky finish. Works on all reactive bowling ballsDesigned to be absorbed into the bowling ballBowling ball remains super tacky longerUse before and after bowling onlyUse That Purple Stuff or That Wow Factor Ball Cleaner to enhance the effectRestores performance to old bowling ballsExtends the life of your bowling ballSafe for use
Content: 0.236 Liter (€109.96 / 1 Liter)
That Wow Factor | Ball Cleaner - 8oz (236ml)
That Wow Factor Ball Cleaner provides the tacky feel and consistent reaction you've come to love about That Purple Stuff BUT it is a stronger formula designed for use before and after competition. Now with a convenient spray top!The video below uses Kegel's Specto Lidar System to compare That Wow Factor Ball Cleaner with That Purple Stuff.
Content: 0.237 Liter (€105.27 / 1 Liter)
CtD Ball Cup
Hold your extra bowling ball with this plastic ball cup.
Big Amazing Microfiber Pad (BAM)
This pad is a 7.5 inch circle with 5 (that's right FIVE) layers for the best clean out there. The textured microfiber layer is made to be used dry during competition or wet with our cleaners when not competing. The black leather layer is also great for using dry during competition.Inside, there are TWO layers of sherpa PLUS a waterproof rubber layer. It feels great in your hand AND easily wipes away dirt and oil while bowling. This pad is washable and reusable. Click here for cleaning instructions. NOTE: Do not use fabric softener
TruCut Scuff Mark Remover ULTRA
TruCut Scuff Mark Remover ULTRA takes the cleaning power of a TruCut Scuff Mark Remover and beefs it up by adding a TruCut Stable Grit Surface to one side.By adding this surface, you can now get rid of those "EXTRA" tough belt marks and scuff marks without all the scrubbing. This means the TruCut Scuff Mark Remover ULTRA will last longer and clean better than the TruCut Scuff Mark Remover. Simply pair with Life After Death Bowling Ball Cleaner + Life Extender or So Fresh & So Clean Bowling Ball Life Extender for a fast and easy way to clean your bowling balls. Do not use this product dry as this will damage the TruCut Scuff Mark Remover ULTRA and change the surface of your bowling ball.For an added bonus, this product can be used around the house for chemical free cleaning of soap scum on shower doors, food burnt on a glass cooktop, or calcium, lime and rust build up on sinks and showerheads. When using around the house, it should ONLY be used with water.Note: If you choose to use this product on your bowling balls first, do not use it around your house. Liquid bowling ball cleaners should not be used as household cleaners.
TruCut Conditioner - 8oz (236ml)
TruCut Conditioner works in five ways: It is made to extend the life of the sanding pad. The conditioner provides a balanced level of lubricity that allows the pad to keep cutting, while dramatically reducing the friction created during the sanding process. Using this product will increase the life of the pad by up to 4 times compared to using the pad dry. This product allows for a cleaner cut. Which means it will leave a more consistent finish. It traps the dust and allows it to pass through the TruCut Sanding Pad. This allows the pad to cut faster and longer. It rejuvenates at the same time. You can literally feel a difference after using this product. When used as directed, this product is made to reduce the amount of dust created which speeds up the sanding process and lowers the mess involved with sanding your ball. Best of all this product is safe to use with any type of bowling ball coverstock. TruCut Conditioner is NOT a bowling ball cleaner. That Purple Stuff or That Wow Factor Ball Cleaner are bowling ball cleaners. TruCut Conditioner is made to be used on your TruCut Sanding Pad. It's red in color and has a clean strawberry scent. This product is safe to use on all bowling balls. It can be used by hand, ball spinner, resurfacing machine, or PYB system. Directions for use Place the ball in a ball cup with the bowling grip face up.Select the desired TruCut sanding pad grit you want to use.Place the sanding pad in the middle of a CtD Power Pad.Generously spray around 20- 25 times covering the entire sanding pad with TruCut Conditioner.Sand the ball with moderate pressure by hand in circular motions on ½ of the ball working from the side to the top of the ball.Flip the ball over and repeat steps 4 and 5.If needed proceed to the next TruCut Sanding Pad grit and repeat the process until all the sanding steps are complete.Remove the sanding pad from the CtD Power Pad and wipe any excess dust off of the ball with the Power Pad and you are ready to go. .Once finished allow the sanding pad and CtD Power pad to completely air dry. For ball spinner use just spray TruCut Conditioner directly on the desired sanding grit pad, and while the spinner is on go up and down on the sides and top of the ball. Add additional sprays to the sanding pad to keep it wet. For Resurfacing Machines use in place of water. This product can be reused.
Content: 0.237 Liter (€105.27 / 1 Liter)
TruCut Sanding Pads - Storage Box
The TruCut storage bag is the perfect size for the TruCut sanding pads. It is made of durable nylon material and protects your TruCut pads from accidentally rubbing against your equipment. Both the 5" and 6" pads will fit in the bag. You can purchase the TruCut storage bag separately or together with the TruCut Pads. You can find the matching sets here (just click on the links):TruCut Sanding Pads Kit | 5"TruCut Sanding Pads Kit | 6"
TruCut Stabilipad | 5"
1 inch thickFlexible foam coreHook velcro on one sideLoop velcro on the opposite sideIt can be used dry or wet Flexible foam allows it to conform better to the shape of the ball while offering stable support for your hand Attaching a TruCut Sanding Pad to the Stabilipad makes it easier to hold and control when adjusting the surface of a bowling ball. The Stabilipad can be used with the CtD Surface Mitt or even a resurfacing machine.