CtD | Creating The Difference - TruCut Sanding Pads
CtD Surfacing Mitt
Bowlers love using TruCut sanding pads, but dislike getting their hands dirty. The best way to sand any bowling ball is using TruCut Sanding Pads with TruCut Conditioner. TruCut Conditioner doubles the life of the sanding pad, improves the consistency of the cut, and reduces the amount of dirt and debris left on the ball.This is great, but you can still get your hands dirty when sa sanding your ball by hand or using a spinner. So we created an easy to use CtD Surfacing Mitt. This product has cross shaped Velcro on one side to hold any TruCut sanding pad or TruCut Premium Polishing pad and features a leather like vinyl material on the other side. It is easy to clean by just wiping it with TruCut Conditioner and a dry cloth after use. It is one size fits all and can be folded in half for storage.This protective mitt will keep your hand dry and that makes it easy to get right to bowling after altering the surface of a bowling ball. Remember you can only do this before or after competition.
TruCut Sanding Pads - 5" Multi Packs: 6-Pack
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Diameter of 5 inches - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 5" Multi Packs: 7-Pack
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Diameter of 5 inches - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 5" Singles
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Diameter of 5 inches - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 6" Multi Packs: 10-Pack
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 80, 120, 220/240- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 6" Multi Packs: 6-Pack
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 80, 120, 220/240- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 6" Multi Packs: 7-Pack
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 80, 120, 220/240- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - 6" Singles
The new TruCut by CtD pads are specifically designed for bowling balls. These pads provide a longer lasting, true cut that resists "lane shine" and improves ball durability and performance. Comparison of close-up images of a TruCut by CtD and an Abralon pad: Available in the following grits:- 80, 120, 220/240- 500, 1000, 1500, 2000, 3000, 4000, P5000D (4000 by hand, 5000 on a ball spinner)Advantages:- longer lasting- brings the surface to the specified grit number - reusable and easy to clean - easier to use when dry or wet sanding - Open honeycomb structureFor small changes before or after play:Apply the pad to the surface of the bowling ball with moderate pressure using small circles. Move around the sides of the ball first and then upward. Repeat twice to work the entire half of the bowling ball. Then turn it over and repeat the process on the other half. Apply a little That Purple Stuff to a CtD Power Pad and wipe the dust off the bowling ball.For use on a ball spinner:Spray TruCut Sanding Pad with TruCut Conditioner. Turn the spinner on low speed and apply the pad to the surface of the bowling ball with moderate pressure. Move the pad back and forth from the top of the ball to the sides of the ball for 5 seconds. Turn the ball over and repeat on all 4 sides for even results.IMPORTANT NOTICE:Write the grit numbers on the back of the pads with a permanent marker..Cleaning Instructions: For dry use - tap the pad on a hard surface to get the dust out. For wet use - hold the pad under running water and flatten. DO NOT CRUMPLE.
TruCut Sanding Pads - Storage Box
The TruCut storage bag is the perfect size for the TruCut sanding pads. It is made of durable nylon material and protects your TruCut pads from accidentally rubbing against your equipment. Both the 5" and 6" pads will fit in the bag. You can purchase the TruCut storage bag separately or together with the TruCut Pads. You can find the matching sets here (just click on the links):TruCut Sanding Pads Kit | 5"TruCut Sanding Pads Kit | 6"
TruCut Stabilipad | 5"
1 inch thickFlexible foam coreHook velcro on one sideLoop velcro on the opposite sideIt can be used dry or wet Flexible foam allows it to conform better to the shape of the ball while offering stable support for your hand Attaching a TruCut Sanding Pad to the Stabilipad makes it easier to hold and control when adjusting the surface of a bowling ball. The Stabilipad can be used with the CtD Surface Mitt or even a resurfacing machine.